Custom Land Rover Series & Defender Parts

Search results for 'tub panel'

23 Item(s)

per page

List  Grid 

Set Ascending Direction
  1. High Tensile Stainless Steel Bolts for Defender NAS Roll Cage (*sold individually*, available in bare stainless or black oxide coated)

    High Tensile Stainless Steel Bolts for Defender NAS Roll Cage (*sold individually*, available in bare stainless or black oxide coated)

    $4.00

    This replacement bolt corresponds to the original Land Rover part number ALR5549, and these are stainless steel replacements used to attach a NAS roll cage to a Defender. Please note that this replacement hardware is a HIGH TENSILE STAINLESS STEEL in Grade A2-80 providing a minimum tensile strength of approximately 115,000 psi. Available in bare stainless or black oxide finish. Price per piece, optional add-on replacement nyloc nut & isolating washers also available. Learn More
  2. LHD Lower Dash Switch Plate Panel (3 Carling)

    LHD Lower Dash Switch Plate Panel (3 Carling)

    $45.00

    NAS [North American Spec] or LHD (Left Hand Drive) Lower Dash Switch Plate Panel (3 Carling Switches) for Land Rover Defender. Learn More
  3. Rear Defrost Switch Wiring Harness (*includes* Carling Switch & Multiplug)

    Rear Defrost Switch Wiring Harness (*includes* Carling Switch & Multiplug)

    $45.00

    Upgrade your Rear Defrost Switch to a Carling using our custom harness combines the reliability of the Carling Switch with an easy way to swap out your old Defrost switch with our plug-and-play replacement to proactively avoid potential issues going forward, or correct/replace a switch that has already failed. We utilize specialty 3.0mm male pin connectors on the end of the harness that specifically mate up directly into the female openings in the Rover plug. This harness is a neat and tidy way to changeover to a Carling Switch, and comes with a color-coded set of instructions/legend for each wire; in addition the end of each wire is clearly labeled, and also includes a visual diagram to also show you where to plug each connector. Learn More
  4. Dash Center Face Plate Panel (VDO-2x 12v-VDO)

    Dash Center Face Plate Panel (VDO-2x 12v-VDO)

    $85.00

    Dash Center Face Plate Panel (2x VDO / Round Gauges & 2x 12V socket) for Land Rover Defender. Learn More
  5. Interior Door Pull/Grab Handles (set of 2)

    Interior Door Pull/Grab Handles (set of 2)

    $140.00

    CNC milled aluminum replacement interior door handles (SET of 2) Learn More
  6. DIN bay for Land Rover Defender Puma/Td4

    DIN bay for Land Rover Defender Puma/Td4

    $100.00

    DIN bay for mounting under the glove box, for vehicles from model year 2007+ with 2.4l and 2.2l engine, ideal for installation of CB, radio or switches .< Learn More
  7. Hazard Switch Wiring Harness (*includes* Carling Hazard Switch & Multiplug)

    Hazard Switch Wiring Harness (*includes* Carling Hazard Switch & Multiplug)

    $75.00

    Failure and internal delamination of the of the Land Rover Hazard Switch #AFU4209L (for NAS/North American Spec vehicles), and #YUF101490 (for imported ROW/Rest Of World vehicles) is a common issue. Our harness combines the reliability of the Carling Hazard Switch with an easy way to swap out your old hazard switch with our plug-and-play replacement to proactively avoid potential issues going forward, or correct/replace a hazard switch that has already failed. This harness uses correctly sized 3mm pin connectors to connect to the factory wiring plug so you do not have to cut or splice the factory wires. INCLUDES your choice of either a black or red Carling Hazard Switch & Multiplug Connector. Learn More
  8. Dash Center Face Plate Panel (12V-Carling-12V)

    Dash Center Face Plate Panel (12V-Carling-12V)

    $85.00

    Dash Center Face Plate Panel (12V-Carling Switches-12V) for Land Rover Defender. Learn More
  9. Yamaha TW200 Quick Release Seat Bolts (Set of 2)

    Yamaha TW200 Quick Release Seat Bolts (Set of 2)

    $40.00

    Custom extended seat bolts compatible with the 1987-2020 Yamaha TW200. The factory recessed bolts are difficult to access, and also make any "field repairs" to the battery or getting under the seat very difficult. Our custom seat bolt solution features a knurled end for ease of threading the bolts in-or-out by hand, and also have a 6-point wrench knockout that fits a standard 10mm wrench to tighten/loosen. We've also made the knockout area large enough to accept an adjustable wrench, or pliers in a pinch for tightening or loosening the seat bolts. Turned on a CNC lathe from a solid piece of 304 annealed stainless steel, they are guaranteed not to rust or corrode. Price is for a SET OF 2. MADE IN THE USA! Learn More
  10. Defender Footwell Panels [***6-8 WEEK PRODUCTION LEAD-TIME***]

    Defender Footwell Panels [***6-8 WEEK PRODUCTION LEAD-TIME***]

    $100.00

    [THIS ITEM IS CUSTOM MADE TO ORDER BASED ON VEHICLE CONFIGURATION, ESTIMATED PRODUCTION LEAD TIME IS APPROX. 6-8 WEEKS.]. Aluminum panels to replace the missing or worn out stock cardboard units. Panels are made from sturdy .063 aluminum plate that is waterjet cut. Panels are currently available for all NAS and LHD (Left-Hand Drive) models (90's, 110’s, and 130's). RHD (Right-Hand Drive) panels are NOT available yet, but are coming soon. Learn More
  11. Dash Center Face Plate Panel (VDO Gauges)

    Dash Center Face Plate Panel (VDO Gauges)

    $85.00

    Dash Center Face Plate Panel (VDO / Round Gauges) for Land Rover Defender. Learn More
  12. Tailgate Organizer for Land Rover Defender

    Tailgate Organizer for Land Rover Defender

    $225.00

    Where to put all the little odds and ends in an expedition vehicle? First-aid kid, multimeter, work gloves, winch controls, tire repair kit, etc....all these things have to be put somewhere. Our tailgate organizer makes use of the mostly unused space on the rear door. In several pockets attached with MOLLE attachment system you can store away all these bits and pieces which then are at hand once needed. Learn More
  13. Defender 90 ST (NAS) Stainless Hardware Kit (Exterior & Interior)

    Defender 90 ST (NAS) Stainless Hardware Kit (Exterior & Interior)

    $275.00

    This exterior/interior stainless steel bolt/screw hardware kit fits a NAS 90 Soft Top configuration, and contains approximately 632 pieces. All bolt packages are clearly labeled and packaged for ease of installation (29 separate packages). The kit includes stainless hardware for the EXTERIOR and the INTERIOR of the NAS 90 Soft-Top vehicles.
    Learn More
  14. Dash Center Face Plate Panel (VDO-3x Carling-VDO)

    Dash Center Face Plate Panel (VDO-3x Carling-VDO)

    $85.00

    Dash Center Face Plate Panel (VDO-3x Carling Switches-VDO) for Land Rover Defender. Learn More
  15. RHD Lower Dash Switch Plate Panel (3 Carling)

    RHD Lower Dash Switch Plate Panel (3 Carling)

    $45.00

    RHD [Right Hand Drive] Lower Dash Switch Plate Panel (3 Carling Switches) for Land Rover Defender. Learn More
  16. Land Rover Defender 90/110/130 Battery Disconnect Switch Kit (battery isolation)

    Land Rover Defender 90/110/130 Battery Disconnect Switch Kit (battery isolation)

    $180.00

    As an essential component of your electrical system, this Battery Disconnect Switch Kit is a high amperage, in-line isolation solution, designed to isolate your vehicle’s battery from the rest of your electrical system. It can by used to disconnect power in emergency situations, while servicing your vehicle or even locked as a mild theft-deterrent. This premium, fully-sealed ‘made-to-go-anywhere’ switch is weather-resistant to IP65 and is able to withstand the harshest of operating conditions. Off-road-ready, these spring-loaded switches are used throughout Europe in military, commercial and agricultural applications for their vibration resistance and high surge tolerances. Learn More
  17. Dash Center Face Plate Panel (VDO-12v-VDO)

    Dash Center Face Plate Panel (VDO-12v-VDO)

    $85.00

    Dash Center Face Plate Panel (2x VDO / Round Gauges & 12V socket) for Land Rover Defender. Learn More
  18. "Land Rover 127" decal for upper grille panel (layered silver over black vinyl)

    "Land Rover 127" decal for upper grille panel (layered silver over black vinyl)

    $10.00

    Reproduction decal for the front upper grille panel / surround on a Land Rover 127, made from layered silver over black vinyl. Measures 11-1/4" x 1-3/8". Learn More
  19. Rear Wash/Wipe Switch Wiring Harness (*includes* Carling Switch & Multiplug)

    Rear Wash/Wipe Switch Wiring Harness (*includes* Carling Switch & Multiplug)

    $65.00

    Upgrading the factory wash/wipe Carling switch, from the clunky factory knob & switch (original part #PRC4454 & PRC4449) is a popular upgrade. Our harness combines the reliability of the Carling Wash/Wipe Switch with an easy way to swap out your old switch with our plug-and-play replacement. For imported / Rest of World (ROW) trucks only, will NOT fit North American Spec (NAS) vehicles). Learn More
  20. Defender 90/110 INTERIOR Stainless Hardware Kit

    Defender 90/110 INTERIOR Stainless Hardware Kit

    $125.00

    This is an INTERIOR ONLY stainless steel bolt/screw hardware kit to fit a Land Rover Defender 90/110, and contains approximately 360 pieces. All bolt packages are clearly labeled and packaged for ease of installation (16 separate packages). The kit includes stainless hardware for: Lower Dash, Instrument Panel, Heater Controls & Center Dash, Dash & Visors, Demister/Defrost Vents, Windshield Pillars, Driver Side End Cap, Tray Trim, Door Panels (ST), Check Strap & Cover, Kick Panel Trim., Floor Pans, Door Sills, Rear Fender Brackets, Seat Rail Bolts, Rear Door Trim (if applicable). Learn More
  21. Dash Center Face Plate Panel (6 Carling)

    Dash Center Face Plate Panel (6 Carling)

    $85.00

    Dash Center Face Plate Panel (6 Carling Switches) for Land Rover Defender. Learn More
  22. Dash Panel & Interior Lights Wiring Harness (*includes* Carling Switch & Multiplug)

    Dash Panel & Interior Lights Wiring Harness (*includes* Carling Switch & Multiplug)

    $65.00

    Failure of the factory switch that controls the Dash Lamp/Panel Lights & Interior Lights (corresponding to original part #PRC7371, generally used on Defender vehicles through the 1994 model year) is a common issue. Our custom harness combines the reliability of the Carling Switch with an easy way to swap out your old Dash Lamp/Panel Lights & Interior Lights switch with our plug-and-play replacement to proactively avoid potential issues going forward, or correct/replace a switch that has already failed. We utilize specialty 3.0mm male pin connectors on the end of the harness that specifically mate up directly into the female openings in the Rover plug. Learn More
  23. NAS Defender Crossbars (set of 2) [***3-6 WEEK PRODUCTION LEAD-TIME***]

    NAS Defender Crossbars (set of 2) [***3-6 WEEK PRODUCTION LEAD-TIME***]

    $500.00

    [THIS ITEM IS CUSTOM MADE TO ORDER, ESTIMATED PRODUCTION LEAD TIME IS APPROX. 3-6 WEEKS]. These crossbars run from the front side rollbars on a NAS (North American Spec) Defender and allow roof racks, baskets, and similar to be mounted safely to the top of your vehicle (note: rack and/or basket NOT included). These units are constructed from 1-1/2" steel tubing, and utilize custom fabrication collar clamps and mounts to secure them in place. Available in two finishes - painted black or powdercoated black (add +2 week to lead-time for powdercoating). Note: our painted *AND* powdercoated versions have a very slight texture to it, which helps to resist marring when mounting baskets/etc on and off from the bars. Learn More

23 Item(s)

per page

List  Grid 

Set Ascending Direction