Custom Land Rover Series & Defender Parts

Roof Racks

Roof Racks & Accessories

9 Item(s)

per page

List  Grid 

Set Descending Direction
  1. NAS Defender Crossbars (set of 2) [***3-6 WEEK PRODUCTION LEAD-TIME***]

    NAS Defender Crossbars (set of 2) [***3-6 WEEK PRODUCTION LEAD-TIME***]

    $475.00

    [THIS ITEM IS CUSTOM MADE TO ORDER, ESTIMATED PRODUCTION LEAD TIME IS APPROX. 3-6 WEEKS]. These crossbars run from the front side rollbars on a NAS (North American Spec) Defender and allow roof racks, baskets, and similar to be mounted safely to the top of your vehicle (note: rack and/or basket NOT included). These units are constructed from 1-1/2" steel tubing, and utilize custom fabrication collar clamps and mounts to secure them in place. Available in two finishes - painted black or powdercoated black (add +2 week to lead-time for powdercoating). Note: our painted *AND* powdercoated versions have a very slight texture to it, which helps to resist marring when mounting baskets/etc on and off from the bars. Learn More
  2. CargoBear - Modular Roof Rack System for Land Rover Defender [***3-6 WEEK LEAD-TIME***]

    CargoBear - Modular Roof Rack System for Land Rover Defender [***3-6 WEEK LEAD-TIME***]

    $1,350.00

    [THIS ITEM IS CUSTOM ORDERED BASED ON VEHICLE CONFIGURATION, ESTIMATED LEAD TIME IS APPROX. 3-6 WEEKS.] The CargoBear is a modular roof rack system made from an aluminum-magnesium alloy and then high-quality powder-coated. They are completely separable - and infinitely flexible to configure to your desired needs. The rack is extremely low-profile ,and sits just 2.35" (60mm) above the roof height, making them one of the thinnest roof racks on the market. Thanks to the lashing rails, you can flexibly secure a roof load anywhere on the rack. Each section is equipped with three plates of coated diamond plate, which can be used and left installed as the "floor" - but not required (in other words you can leave the plates out of the rack, so just the rails are in place with no floor). Whether you need a full-length carrier for your 110 Defender or just a short platform, the CargoBear is optimally tuned and adjustable to your requirements. Learn More
  3. CargoBear Quick-Mounting Tent Frame

    CargoBear Quick-Mounting Tent Frame

    $450.00

    The roof-top quick-change system consists of two stainless steel frames (an upper and lower part). The lower part is powder-coated black and is attached to the vehicle, the top of the frame is mounted on the tent. This system is suitable for all roof racks, and the assembly and disassembly takes place quickly - only four screws have to be removed. Additionally, because of the even geometric nature of the tent frame, the tent can also be easily rotated at a 90 ° angle for changing the opening/access from front of the rack to side (or vice-versa). Learn More
  4. CargoBear Awning Holder Bracket Set (EACH BRACKET SET SOLD INDIVIDUALLY - 2 required / 4 recommended)

    CargoBear Awning Holder Bracket Set (EACH BRACKET SET SOLD INDIVIDUALLY - 2 required / 4 recommended)

    $60.00

    The CargoBear awning holder allows the installation of numerous awnings or awnings on the CargoBear Roof Rack. At least two (2) CargoBear bracket sets are required for assembly. The Awning Bracket set comes with the required mounting material for attaching the awning holder to the CargoBear roof rack. Fixing material for the awning is not included. The awning brackets are made of stainless steel, and can be used on all CargoBear carriers with 30° angled feet. Learn More
  5. CargoBear Auxiliary / Worklight Bracket (EACH BRACKET SOLD INDIVIDUALLY)

    CargoBear Auxiliary / Worklight Bracket (EACH BRACKET SOLD INDIVIDUALLY)

    $35.00

    The CargoBear auxiliary / worklight bracket allows the installation of additional lights, such as fog lights, flood or spot lights, rear worklights, etc. The worklight brackets are made of stainless steel and powdercoated black, and can be used on all CargoBear roof rack systems. Price is per bracket (1), and does not include lights. Learn More
  6. CargoBear CB Antenna Bracket

    CargoBear CB Antenna Bracket

    $25.00

    The CargoBear CB Antenna bracket allows the installation of any exterior antenna. The bracket is made of stainless steel and powdercoated black, and can be used on all CargoBear roof rack systems. Price is per bracket (1), and does not include antenna. Learn More
  7. CargoBear 'Connector Bar' for LED light-bar (BRACKETS SOLD SEPARATELY)

    CargoBear 'Connector Bar' for LED light-bar (BRACKETS SOLD SEPARATELY)

    $40.00

    Connector Bar for LED light-bar or similar. Can be used on the front of the rack, either offset to the side(s) OR in the center on the front of the rack (see technical drawings). Suitable for universal accessories such as light bars or similar. Supplied *without* side brackets necessary for mounting (2 required) and without auxiliary lights. Please order the mounting brackets separately here: CargoBear Brackets for Connector Bar (2 brackets required per Connector Bar). Learn More
  8. CargoBear Bracket for 'Connector Bar' or smaller worklights (EACH BRACKET SOLD INDIVIDUALLY)

    CargoBear Bracket for 'Connector Bar' or smaller worklights (EACH BRACKET SOLD INDIVIDUALLY)

    $20.00

    Brackets for the CargoBear Connector Bar (2 required for each Connector Bar), or to be used for additional smaller worklights / auxiliary lights. Each Bracket sold separately. Made from stainless steel and powdercoated black. Learn More
  9. Lashing rail fitting, double stud

    Lashing rail fitting, double stud

    $7.00

    Double Stud Fitting for Airline Cargo lashing rails, load capacity 2425lbs (1100kg), ring diameter 1.57" (40mm). Units are manufactured to ISO 9788 specs, made from galvanized steel and are UV and salt water resistant. For use with the CargoBear Roof Rack system. Learn More

9 Item(s)

per page

List  Grid 

Set Descending Direction